JetsonsAge

Explore the frontier.

Search published reporting, intelligence and briefs.

Explore JetsonsAge

KAIST Fits a Working Battery Inside a Curved Drone Component

The lithium-sulfur prototype lit an LED from within a drone-leg geometry. A separate test measured what happened to cell capacity when the pouch was held in a curve.

Published November 19, 2026Intelligence / Materials / Advanced Composites

A KAIST-led team fitted a lithium-sulfur pouch cell into a curved drone-leg component and used it to light an LED. The experiment showed that a cell could still supply power after installation in an awkward cavity. KAIST announced the work on November 18; the paper appeared on October 1 in Advanced Composites and Hybrid Materials.

Curves are a problem for a battery electrode because the layers can crack, separate or lose electrical contact when held in shape. In the KAIST design, a woven carbon cloth carries current through the electrode. The researchers grew nickel cobalt selenide nanowires directly on the cloth to give the sulfur electrode a connected support.

The nanowires also help retain lithium polysulfides, soluble compounds that form as sulfur cells charge and discharge. When those compounds move away from the electrode, they can contribute to capacity loss. The coating addresses that chemical problem while preserving contact between the nanowires and the cloth under bending.

What held up under a bend

The team bent the electrode scaffold around a radius of 2.5 millimeters 1,000 times. It then examined the interface and tested cells built with the conditioned electrodes. This was a mechanical test of the electrode scaffold followed by electrical tests of assembled cells.

In a separate measurement, a pouch held in a cylindrical shape delivered 94% of the capacity measured for the flat configuration. That number describes capacity while curved. The paper also shows cells operating after being fitted into cylindrical, oval and square shapes as well as the drone-leg geometry. The drone-leg demonstration measured operability by lighting an LED; it did not test propulsion or show that the battery carried the leg’s structural loads.

The study’s baseline used relatively low sulfur loading, generous electrolyte and slow discharge. Putting the design into a working aircraft would call for a full component comparison: how much weight the cell and its enclosure add or replace, what loads the assembled part can sustain, and how much energy remains usable at the power levels required for flight.

What happened when the plastic frame broke

The most informative moment came in a load fixture. The researchers compressed the cylindrical plastic frame in steps while monitoring the pouch through a 44-kilohm resistor. The frame fractured. Across the loading sequence the measured voltage changed from 2.457 to 2.452 volts. The pouch had contributed to the mechanical response, and the electrical path survived that particular event. Those are two distinct observations that a photograph of an LED cannot supply. Research paper, figure 6

The size of the resistor puts the demonstration in perspective. At 2.45 volts, Ohm’s law gives a current of roughly 56 microamps, or about 0.14 milliwatts of power. Maintaining voltage under that small load is a sensitive way to detect an open circuit. It leaves unanswered how a damaged cell would behave under a propulsion load or after charging again. For a serviceable aircraft leg, an operator would need a way to tell whether a landing had damaged the cell even when the terminal voltage still looked normal. The test makes that maintenance question more concrete than a general claim that a battery can bend.

The missing denominator is the area of the leg

The paper gives the curved cell’s capacity as 1,117 milliamp-hours per gram of sulfur at a slow 0.02C discharge, compared with 1,188 for the flat cell. The paper’s roughly one milligram of sulfur per square centimeter makes the curved figure about 1.12 milliamp-hours per square centimeter of electrode. That conversion matters to someone drawing an actual component. The designer has a fixed area inside the leg, and the published value per gram counts sulfur alone. The finished part also carries current collectors, electrolyte, packaging and whatever material takes the load when the craft lands. KAIST team’s paper

A useful next comparison would weigh the complete curved leg and measure its usable energy after a representative series of landings. Then do the same for an ordinary leg and a separate battery that together weigh as much. Lighting an LED established electrical continuity in an awkward shape. The matched comparison would show whether putting the energy there earns the aircraft more flight time, better use of interior space, or a new component that is expensive to replace after a hard landing.

Sources

KAIST’s November 18 announcement · Research paper

Sources · 2
More intelligence